Shanghai Richeng Electronics Co. Ltd - ISO9001/IATF16949/ISO/TS22163
Choose Language

Wiring duct,Cable Gland,Cable Tie,Terminals,RCCN

Injection molding machine waste heat recovery energy saving program to achieve energy saving and environmental protection double effect

On our planet, every day by the smoke away the huge heat, the pollution caused by the environment is amazing. Injection molding industry how to save energy and reduce emissions, improve the working environment, reduce the temperature of the injection workshop is a matter of concern. The waste heat recovery of the injection molding machine is an important aspect of energy conservation work, if the heat of all the flue gas are recycled, the economic benefits are very impressive.

1 energy saving program

The existing injection molding machine is equipped with a drying machine for dehumidifying and drying plastic, and the heat is supplied by means of electric heating. The air discharged from the air outlet of the insulated drying drum carries a certain amount of heat. If this part of the heat is directly discharged into the workshop, The area will increase the dust content of the workshop air and affect the health of the workers, on the other hand will increase the energy consumption and increase the economic burden of enterprises.

In view of the shortcomings of the prior art, there is provided a waste heat recovery thermal cycle device in which a waste heat collecting device is installed around the heating section of the melt cylinder, and the plastic in the drying drum is dried and dehumidified by the heat dissipated at work.

The hot air with a certain amount of water and dust is discharged from the pipe and enters the hot air circulation dehumidifying filter device 3, and is processed by 3, and thereafter the hot gas is partially heated by the heat source to adjust the fan 6 to provide heat for the hot gas in 1, The heat of the other part of the hot air and 2 after the heating of the gas through 5, which can be adjusted by the air flow rate of 6 within the temperature , Guarantee 4 corresponds to the actual set temperature. When the temperature within the 4 is lower than the set, 5 to send the signal to 6, increase the speed increase the output air volume, in the 6 drive effect, enter 4, by 2 high temperature air, 4 within the temperature rise, when 4 The temperature is higher than the set temperature, 5 send a signal to 6, reduce the speed of 6, reduce the output air volume, so enter the 4 high temperature gas reduction, 4 within the temperature [4] (see Figure 1).

(1 - waste heat collection heat storage system 2 - waste heat collection heaters 3 - hot air circulation dehumidification filter device 4 - insulation drying bucket 5 - intelligent cycle adjustment device 6 - heat source adjustment fan 7 - collector pipe 8 - heat source pipeline 9 - auxiliary heating equipment)

Analysis of Economic Benefit

2.1 Technical characteristics

(1) system power saving 15% to 35%, dryer more than 90%

(2) high temperature 270 ℃ ~ 280 ℃, low temperature -70 ℃;

(3) the production workshop temperature drop of up to 3 ° ~ 8 °, the working environment greatly improved;

(4) CO2 emissions are reduced by 45% to 50% compared to conventional and no SO2, fly ash, ash and NOx emissions;

(5) Tensile strength ≥ 0.02 MPa;

(6) corrosion-resistant, aging, waterproof, anti-oil, anti-oil, environmental protection, pollution

(7) easy to install, repair, good toughness, easy bending dressing;

(8) for different temperature, shape of the injection molding machine.

2.2 Case Study

Case analysis is shown in Table 1.

According to Table 1, the annual energy saving of each machine is: 2.53 * 24 * 365 * 0.918 = 20400 The whole system can save 14t and 15t of carbon dioxide per year.

In view of this, greatly reducing the cost, saving the traditional dryer waste power distribution system capacity power, greatly improving the use of power, the extra power can be used as other equipment without the need to install the transformer, if the workshop needs to use air conditioning, It can save a lot of air conditioning costs; due to the waste heat of the melt barrel is recycled, independent installation of the double filter intake device, can make each injection molding machine will not be contaminated, and can completely filter the barrel Of the dust drift, to prevent the workshop gas pollution, the health of the staff play a protective role, the production plant temperature drop of up to 3 ° ~ 8 °, the real solution to the workshop high temperature problem, the staff in a comfortable working environment jobs.

 


3 waste heat utilization problems and suggestions

The problems are as follows.

(1) China's plastics processing enterprises throughout the country, but the uneven level of equipment and technology, many enterprises need to further technological transformation of equipment;

(2) the industry ban plastic sound endless, but in the rural market is still a lot of use of plastic products, compression costs have become the most important business development;

(3) due to the dissemination of information channels and enterprises lack of funds, greatly restricting the large-scale promotion of this technology, many companies lack of energy-saving technologies and clean development mechanism and other advanced mechanisms, domestic and foreign advanced technology service providers have no way to understand the situation of enterprises;

(4) high-temperature waste heat utilization technology has been more mature for many years, the success of the case also shows its economic benefits, but the potential of large and medium temperature waste heat utilization still need further development.

The corresponding recommendations are described below.

(1) the production enterprises to the management and use of "proper use, scientific management, careful maintenance, regular maintenance, reasonable lubrication, planned maintenance, improve equipment in good condition, so that equipment in good condition;

(2) pollution of energy consumption is also the most important, the use of heat as one of the main force of energy conservation, should introduce more positive policies to give the appropriate financial support to guide enterprises in the waste heat recovery industry play an active role;

(3) to carry out research on waste heat resources, to collect relevant advanced technology, management and case to strengthen the dissemination of information to strengthen the research of low and medium heat and heat utilization technology to promote the application of waste heat technology.

(4) the proposed waste utilization potential of the enterprise, as far as possible the system to consider, the overall improvement, and pay attention to the fine use of automatic control system.

Related articles

Previous: Selection of connector plugs
Next: Common Problems and Solutions of PVC Trunking Production
On-line
contact
message
download
Print
WeChat WeChat
Collection
TOP